streamgym9

How to Replace the Replacement Key Battery For the Saab 9-3 Saab owners have a distinct set of steps to add another key. This requires the use of a handheld computer, known as Tech-2, to be used by the dealer. Then, a new transponder and key must be purchased. Rotate your keys to prevent one from wearing out more than the other. This will help keep your keys in top condition. Replacement Case The new key fobs for keys are not like the older Saab keys. They feature electronic components which make it hard to copy. That has made car theft considerably more complicated than it was 20 years ago. However, it also has made the replacement of lost keys a much more expensive endeavor. Every owner of a 9-3 Saab should have at least two working keys. It is costly to replace a lost key, as it requires replacing the CIM module, and reconfiguring the locking cylinders. Dealers typically charge between $100 and $200 to complete this. There are ways to avoid these high costs. Some parts dealers will look up the code from an old key (usually the same one that opens the doors and switches the ignition) and cut a brand new metal key blade for only a fraction of the dealer's cost. The key must be exactly the identical to the original one for it to work in your vehicle. Follow these steps to replace the case. You'll need a flathead and a lot of patience. With the screwdriver slowly break the plastic and separate the emergency key from the case. Once the case is open, remove the electronics and put them in the new case. Make sure to insert the correct key and badge back in the case too. Replacement Battery The replacement battery for the Saab 9-3 is a low-cost part that can be replaced easily and quickly. Cyclone's YouTube video Cyd shows how to replace the remote fob battery with just four steps. This tutorial is suitable for any modern-day saab key fob though the process may vary slightly. The first step is to locate the button that will release the backup key inside the fob. It's usually near the Saab logo on the back of the fob. Use a flathead to insert the screwdriver through the small hole in this button. This should be sufficient to open the case to allow you to change the battery. Once you have installed the new battery CR1632, you are able to reassemble the remote key fob. Then, you can program it into your car. The entire process should not take more than an hour or less. This is a straightforward procedure that doesn't require special tools. The procedure is a little more complex if you lose your key, but it is possible. The dealer will first need to read the VIN of the vehicle and order a replacement TWICE module and key blade that has the correct unique code. The dealer will then need to program the key using MDI an innovative software tool. Key Replacement Fob The key fob contains a battery that is used to lock and unlock your vehicle. The batteries are able to last for that is a long time, and they eventually expire. This is a frequent issue with all cars. The good thing is that you can change the batteries in most key fobs without having to replace the entire case. You can buy replacement fobs on Amazon that have all the electronics already installed, which means you can simply open the case and replace those batteries that are old. saab key programming near me is important to note that you'll need to take out the emergency key first. you can accomplish this by inserting the screwdriver of a small flathead into the slot found in the middle of the case. Use the screwdriver to move around the case until it is split open, making it easy to remove. If you're about to replace the keys ensure that you have spare keys, since this will cut down your total cost by a substantial amount. If you have spare keys, you can ask the dealer cut an additional key and program it to the car, which is cheaper than replacing the whole key fob. If you do not have a spare key one, you can add an additional key to your car, but this requires a lot of research and effort. It costs around a hundred dollars to purchase an additional car key. The computer of the car must also be programmed. Professionals can accomplish this however it's a costly option. Replacement Ignition The current SAAB 9-3 has a more sophisticated alarm system based on a key code. This means that in the event that you lose your only functioning key, getting another key can be extremely expensive as the car has to have a computer module added and it also must be specially programmed to accept an extra key. Most locksmiths can't do this or even a dealer will charge several hundred dollars just to program the new key! If you've lost your sole working key and a dealer is able to replace the computer in your car (known as the CIM or SAAB TWICE) in order to make an exchange, and they will charge you a premium price for it. Instead we can reprogram the EEPROM of your current car computer to prepare it for a replacement key, and save you over 50% of the price you have to pay at a dealership. If you've been an owner of a 03-11 SAAB 9-3, then you likely have noticed that the ignition switch isn't all that durable. If the ignition key you have isn't functioning properly, you must consider replacing it. They can become extremely sticky and the buttons can fall off. The good news is that replacing the ignition key isn't as difficult as it sounds and can be done in a short time using the proper tools.